- Scanning
- Frequently Asked Questions
- My Lock won't Connect
- My Lock won't open
- The ShackIe is Stuck Rotated Open at 180˚
- Estimated Battery Life
- Resetting the Lock
- LED & Buzzer Behavior
- Heartbeat
- Charging State
- Sleep State
- Updating Firmware
Scanning
Scanning is done by pressing the button on the top of the lock to activate the scanner. Once pressed, the scanner will illuminate and you can scan a barcode. The video below helps illustrate how to properly scan a barcode, and should be watched before proceeding.
It's also important to note that If the scanner is busy the device will BEEP 3 times for 150 milliseconds each with a 300 millisecond interval between BEEPs.
Because of this it's important that when scanning only one barcode is scanned, and subsequent scans are not done until the success beep is heard from the lock itself. You can also refer to the LED on the bottom of the lock for confirmation. Once the GREEN LED turns off, the lock has finished processing the scan, and is ready for the next.
Frequently Asked Questions
My Lock won't Connect
My Lock won't open
The ShackIe is Stuck Rotated Open at 180˚
In the event that the lock is opened, the shackle is rotated 180˚ from the closed position and something inadvertently triggers the lock switch, the lock can become locked in the open position. If this occurs, open the lock again to release the shackle so that it can be closed correctly.
If this occurs repeatedly, it is possible that the switch on the device is broken and should be replaced.
Estimated Battery Life
Battery life can vary depending on your use case. The largest contributing factor to battery life is how often the lock is set to send status updates back to Control, which can be edited inside of BoxLock Control. We've got an article that speaks to this, linked below.
AccountResetting the Lock
In some situations it's necessary to reset the lock to restore functionality. To do this, you'll hold down the button on the lock for ~10 seconds. When the reset is complete, you'll hear a series of three BEEPs. This is the indicator that the reset is complete, and you can attempt to use the lock again.
LED & Buzzer Behavior
The BoxLock device provides visual feedback to the user via RED, GREEN, PURPLE and BLUE LEDs. The color of the illuminated LED along with the illumination duration and frequency determine the meaning of the visual response.
The BoxLock device provides audio feedback to the user via a buzzer. The BEEP duration, number of BEEPs, and pause interval between BEEPs determine the meaning of the audio feedback.
Heartbeat
The BoxLock device presents a BLUE LED blink every 5 seconds for a duration of 200 milliseconds to indicate an active BoxLock device when the device is not connected to a USB charging source.
Charging State
The BoxLock device presents a solid GREEN LED when the device is connected to a USB charging source to indicate a fully charged device.
The BoxLock device presents a solid YELLOW/ORANGE LED when the device is connected to a USB charging source to indicate a charging device that is not fully charged. All other LEDs are turned OFF .
When the USB-plugged BoxLock device is unplugged from a charging source, the RED and GREEN LEDs are turned OFF .
Sleep State
When the device is idle for 30 seconds and is NOT connected to a USB charging source, the device will enter a deep sleep state to conserve battery until the Main Button is pressed.
Immediately prior to entering deep sleep,
- The device turns the Heartbeat OFF
- The device turns all LEDs OFF
- The device blinks the GREEN LED 3 times with a duration of 100 milliseconds each and a 200-millisecond interval between blinks.
Updating Firmware
When an Firmware Update task is initiated,
- The device turns the Heartbeat OFF
- The device presents a solid PURPLE LED
- The device ensures the RED and GREEN LEDs are turned OFF
When the Firmware Update task is actively downloading,
- The device toggles the PURPLE LED ON and OFF each time 25K bytes are downloaded
When the Firmware Update task completes successfully,
- The device ensures the heartbeat is turned OFF
- The device blinks the PURPLE LED 5 times with an ON duration of 100 milliseconds and an OFF duration of 200 milliseconds
- The device precedes each PURPLE LED blink with a 100-millisecond buzzer BEEP
- The device Restarts
When the Firmware Update task does NOT complete successfully,
- The device buzzer BEEPs for a 1 second duration
- The device presents 5 RED LED blinks with an ON duration of 100 milliseconds and an OFF duration of 200 milliseconds
- The device precedes each RED LED blink with a 100-millisecond buzzer BEEP
- The device turns all LEDs OFF
- The device initiates the Heartbeat